Products

apparatus aggregate impact value pdf

Aggregate Impact value Test Apparatus, Procedure and uses

The apparatus of the aggregate impact value test consists of: A testing machine weighing 45 to 60 kg and having a metal base with a plane lower surface of not less than 30 cm in diameter. Level and plane concrete floor of minimum 45 cm thickness are used to support it. The base of the machine should also have provisions for fixing its base.get price

Request a quoteget price

Determination of Aggregate Impact Value Impact Test on

Feb 22, 2010· Aggregate Impact Value on Coarse Aggregates Apparatus for Aggregate Impact Test. The apparatus as per IS: 2386 (Part IV) 1963 consists of: (i) A testing machine weighing 45 to 60 kg and having a metal base with a painted lower surface of not less than 30 cm in diameter. It is supported on level and plane concrete floor of minimum 45 cmget price

Request a quoteget price

Aggregate Impact Value (AIV) Apparatus Aggregate Impact

Standards. BS 812:112. General Description. The Aggregates Impact Value (AIV) Apparatus is used to determine the aggregate impact value which provides a relative measure of the resistance of an aggregate to sudden shock or impact. The counter fitted to the machine automatically records the number of blows delivered to the sample.get price

Request a quoteget price

Aggregate Impact Value Apparatus Concordia International

The apparatus is used to determine the aggregate impact value which provides a relative measure of the resistance of an aggregate to sudden shock or impact. The apparatus construct by strong rigid steel frame and mechanical blow counter. Inquiry Now!get price

Request a quoteget price

Aggregate Impact Value Test, Procedure, Result & Standards

Aggregate impact value is the ratio of the weight of the fraction passing through 2.36 mm (weight W2) by the total weight of the sample (weight W1 + W2). Aggregate Impact Value = (W2/ (W1+W2)) * 100 = 80 gm / 300 gm = 26.67 (Impact Value) Where, W1= Weight of get price

Request a quoteget price

IS 9377 (1979): Specification for apparatus for aggregate

APPARATUS FOR AGGREGATE IMPACT VALUE 0. FOREWORD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 20 December 1979, after the draft finalized by the Cement and Concrete Sectional Committee had been approved by the Civil Engineering Division Council.get price

Request a quoteget price

Aggregate Impact Value Civil Engineering

The apparatus used for determining aggregate impact value of coarse aggregates is Impact testing machine conforming to IS: 2386 (Part IV)- 1963,IS Sieves of sizes 12.5mm, 10mm and 2.36mm, A cylindrical metal measure of 75mm dia. and 50mm depth, A tamping rod of 10mm circular cross section and 230mm length, rounded at one end and Oven.get price

Request a quoteget price

Aggregate Impact Value Testing AIV TEST Civil

Jan 09, 2018· Aggregate Impact Value Test. AIV test is conducted to determine the Aggregate Impact Value of Coarse aggregate. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from Its resistance to a slow compression load.get price

Request a quoteget price

Impact Value of Aggregate

The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from its resistance to a slow compressive load. . apparatus requiredget price

Request a quoteget price

aggregate impact value apparatus

Aggregate Impact Value Civil Engineering. The apparatus used for determining aggregate impact value of coarse aggregates is Impact testing machine conforming to IS: 2386 (Part IV)- 1963,IS Sieves of sizes 12.5mm, 10mm and 2.36mm, A cylindrical metal measure of 75mm dia. and 50mm depth, A tamping rod of 10mm circular cross section and 230mm length, rounded at one end and Oven.get price

Request a quoteget price

IS 9377 (1979): Specification for apparatus for

IS I 9377 1979 Indian Standard SPECIFICATION FOR APPARATUS FOR AGGREGATE IMPACT VALUE 0. FOREWORD 0.1 This Indian Standard was adopted by the Indian Standards Institution on 20 December 1979, after the draft finalized by the Cement and Concrete Sectional Committee had get price

Request a quoteget price

Aggregate impact value test- step by Step Procedure with

It is expressed in percentage (%). It should be less for high impact bearing aggregate for pavement. In this post I will show you the details of the aggregate impact value test. So, read it carefully to get full knowledge. Apparatus required. Aggregate impact value machine whose weight should be between 45 get price

Request a quoteget price

IS 9377: Specification for apparatus for aggregate impact

Title of Legally Binding Document: Specification for apparatus for aggregate impact value Number of Amendments: Equivalence: Superceding: Superceded by: LEGALLY BINDING DOCUMENT Step Out From the Old to the New--Jawaharlal Nehru Invent a new India using knowledge.--Satyanarayan Gangaram Pitrodaget price

Request a quoteget price

Aggregate Testing Lab Equipment Sun LabTek

We manufacture the best quality equipment related to Aggregate Testing Lab Equipment, that comprises of Sample Splitter, Aggregate Crushing Value Apparatus, Aggregate Impact Tester With Blow Counter, Los Angeles Abrasion Testing Machine, Dorry Abrasion Testing Machine, Devel Attrition Tester, Thickness Gauge, Length Gauge, Cylindrical Measuresget price

Request a quoteget price

Impact Test on Aggregates GharPedia

Aggregate impact value (The value of aggregate impact test) = (W1/W2)*100. The value of aggregate impact test should not be more than 45% by weight of aggregates, used for concrete other than wearing surface. An impact value 35% is permissible for the bituminous macadam. Maximum permissible impact value for the water bound macadam is 40%.get price

Request a quoteget price

Crushing value apparatus (ACV), Aggregates testing

The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Two versions available: 150 (standard) and 75 mm dia. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure.get price

Request a quoteget price

Exp 4 Aggregate Impact Value Civil Engineers PK

Experiment No. 4: Determination of the aggregate impact value of different coarse aggregate samples. (BS 812) Scope & significance: Aggregate Impact Value The aggregate impact value gives a relative measure of the toughness or the resistance of aggregate sudden shock or impact is not proportional to the resistance to a slowly applied compressive load.get price

Request a quoteget price

AGGREGATE CRUSHING VALUE

AGGREGATE CRUSHING VALUE 1.Objective The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead.get price

Request a quoteget price

apparatus aggregate impact value pdf

Aggregate Impact Value to BS812-112 Aggregate Impact Value apparatus with mould to BS812:110 check box to select Ask a question about this Product,Save Page to PDF The page to PDF system has been restored We apologise for any inconvenience & thank you for.get price

Request a quoteget price

Aggregate Impact Tester,Impact Testing Machines,Impact

This Apparatus is used to determine aggregate impact value of coarse aggregate. The hammer of the tester fall freely from 380 mm height on coarse aggregate for 15 times/15 sec.the crushed aggregate removed from the cup ,then sieved and weighed. The % ratio of the weight passing 2.36mm sieve and weight of oven dried sample is Aggregate Impact value.get price

Request a quoteget price

7.7 Aggregate Crushing Value and 10% Fines Value

Figure 7.7.1 Outline form of cylinder and plunger apparatus for the aggregate crushing value and ten percent fines test e) A ventilated oven, thermostatically controlled at a temperature of 1050C plus or minus 50C. f) A rubber mallet, a metal tray of known mass and large enough to contain 3 kg ofget price

Request a quoteget price

DCC3113 DETERMINATION OF AGGREGATE IMPACT VALUE.

Dec 15, 2017· Classification of aggregates using Aggregate Impact Value is as given below: Aggregate Impact Value Classification <20%.= Exceptionally Strong 10 20% .=Strong 20-30%. =Satisfactory for road surfacing >35%.= Weak for road surfacing 5. 5 APPARATUS 1. Aggregate Impact Value Test Machine 2. BS test sieve 3. A metal tamping rod 4.get price

Request a quoteget price

Crushing value apparatus (ACV), Aggregates testing

The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Two versions available: 150 (standard) and 75 mm dia. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure.get price

Request a quoteget price

ELE International Aggregate Impact Value Apparatus

Aggregate Impact Value (AIV) The apparatus has been designed in a particularly heavy duty form, with specially hardened steel surfaces for minimum wear. The assembly is heavily plated to ensure corrosion resistance and forms a rigid frame around the quick-release trigger mechanism, which ensures an effective free fall of the hammer when released.get price

Request a quoteget price

apparatus aggregate impact value pdf

Aggregate Impact Value to BS812-112 Aggregate Impact Value apparatus with mould to BS812:110 check box to select Ask a question about this Product,Save Page to PDF The page to PDF system has been restored We apologise for any inconvenience & thank you for.get price

Request a quoteget price

Aggregate Impact Value to BS812-112 Aggregates Impact

The AIV apparatus consists of a hammer with a trip action release, mould and automatic blow counter. All this is contained within a rigid frame to ensure free-fall of the hammer when released. To determine the Aggregate Impact Value (AIV) of aggregates which provides a relative measure of theget price

Request a quoteget price

Aggregate Impact Tester,Impact Testing Machines,Impact

This Apparatus is used to determine aggregate impact value of coarse aggregate. The hammer of the tester fall freely from 380 mm height on coarse aggregate for 15 times/15 sec.the crushed aggregate removed from the cup ,then sieved and weighed. The % ratio of the weight passing 2.36mm sieve and weight of oven dried sample is Aggregate Impact value.get price

Request a quoteget price

Impact Value Test of Aggregate Procedures, Theory

To determine the aggregate impact value. APPARATUS REQUIRED. 1. An impact testing machine weighing between 45kgs to 60 kgs with a metal base. 2. A cylindrical steel cup having an internal diameter of 102mm, depth of 50mm and thickness of 6.3mm. 3. A metal hammer with the cylindrical lower end and weighing 13.5 to 14kgs.get price

Request a quoteget price

7.7 Aggregate Crushing Value and 10% Fines Value

Figure 7.7.1 Outline form of cylinder and plunger apparatus for the aggregate crushing value and ten percent fines test e) A ventilated oven, thermostatically controlled at a temperature of 1050C plus or minus 50C. f) A rubber mallet, a metal tray of known mass and large enough to contain 3 kg ofget price

Request a quoteget price

AGGREGATE CRUSHING VALUE

AGGREGATE CRUSHING VALUE 1.Objective The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead.get price

Request a quoteget price

Aggregate Crushing Value Test -Determine Aggregate

Aggregate Crushing Value Test. The objective of this test is to: Determine the aggregate crushing value of coarse aggregate; Assess suitability of coarse aggregates for use in different types of road; Apparatus. A steel cylinder 15 cm diameter with plunger and base plate. A straight metal tamping rod 16mm diameter and 45 to 60cm long rounded atget price

Request a quoteget price

DCC3113 DETERMINATION OF AGGREGATE IMPACT VALUE.

Dec 15, 2017· Classification of aggregates using Aggregate Impact Value is as given below: Aggregate Impact Value Classification <20%.= Exceptionally Strong 10 20% .=Strong 20-30%. =Satisfactory for road surfacing >35%.= Weak for road surfacing 5. 5 APPARATUS 1. Aggregate Impact Value Test Machine 2. BS test sieve 3. A metal tamping rod 4.get price

Request a quoteget price

DETERMINATION OF AGGREGATE CRUSHING VALUE

The apparatus of the aggregate impact value test as per IS: 2386 (Part IV) 1963 consists of: 7) A testing machine weighing 45 to 60 kg and having a metal base with a plane lower surface of not less than 30 cm in diameter. It is supported on level and plane concreteget price

Request a quoteget price

IS 2386-4 (1963): Methods of test for aggregates for

IS : 2386 (Part IV) ‘- 1963 2.2 Apparatus The apparatus for the standard test shall consist of following : a) A 15-cm diameter open-ended steel cylinder, with plunger and base-plate, of the general form and dimensions shown in Fig. 1.get price

Request a quoteget price

CE 354 Transportation Engineering Sessional I (Lab Manual)

The aggregate impact value gives a relative measure of the resistance of an aggregate to “sudden shock or impact”, which in some aggregates differs from its resistance to a slowly applied compressive load. With aggregate of aggregate impact value (AIV) higher than 30 the result may be anomalous.get price

Request a quoteget price

Flakiness And Elongation Index TEST Of Coarse Aggregate

This method uses to measure the Flakiness Index and Elongation index of aggregate use in the construction of Highway pavement and concrete structure. Reference:-IS 2386 (Part 1) 1963 Apparatus:-Balance:-The balance used to measure the aggregate has sufficient capacity. It accuracy is 0.1% of the weight of the test sample. Metal gauge:-get price

Request a quoteget price